KZoli: Új oldal, tartalma: „Az ''lm-sensors'' konfigurálása a hardver monitorozás "legszöszögősebb" része. A típusfüggő beállításokat a Debian Squeeze előtt a ''/etc/sensors.conf'' i…”

2018-05-29T20:02:02Z

Új oldal, tartalma: „Az ''lm-sensors'' konfigurálása a hardver monitorozás "legszöszögősebb" része. A típusfüggő beállításokat a Debian Squeeze előtt a ''/etc/sensors.conf'' i…”

Új lap

Az ''lm-sensors'' konfigurálása a hardver monitorozás "legszöszögősebb" része. A típusfüggő beállításokat a Debian Squeeze előtt a ''/etc/sensors.conf'' illetve ''/etc/sensors3.conf'' átírásával vagy lecserélésével lehetett érvényesíteni; a Squeeze-ben és utódaiban már külön (''overlay'', azaz a közös konfigurációs állomány vonatkozó szakaszát felülíró) állományként, a ''/etc/sensors.d'' könyvtárba tehetőek.

Az alábbi receptek konkrét gépek (évek alatt összegyűjtött) beállításai; egy-egy közölt recept másik, hasonló alaplapon vagy gépen nem feltétlenül működik helyesen! Ezért a leírtak erős kritikával értékelendők.

===ABIT TH7-II===
* A szenzor chip I2C ISA buszon csatlakozó Winbond 83627-HF.
* Szükséges kernel modulok: ''i2c_core i2c_dev i2c_i801 w83627hf eeprom''.
<pre>-rw-r--r-- root root /etc/sensors.d/abit-th7-ii

chip "w83637hf-*"

# Voltages

label in0 "VCore"
set in0_min cpu0_vid * 0.95
set in0_max cpu0_vid * 1.05

label in1 "RAMBUS"
set in1_min 2.5 * 0.95
set in1_max 2.5 * 1.05

label in2 "I/O 3.3V"
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05

label in3 "5VCC"
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05

label in4 "12VCC"
compute in4 ((30/10) +1)*@ , @/((30/10) +1)
set in4_min 12 * 0.90
set in4_max 12 * 1.10

label in5 "-12V"
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
set in5_max -12 * 0.90
set in5_min -12 * 1.10

label in6 "-5V"
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14
set in6_max -5 * 0.90
set in6_min -5 * 1.10

label in7 "VBAT"
set in7_min 3.3 * 0.90
set in7_max 3.3 * 1.10

label in8 "Standby"
ignore in8
# compute in8 ? ?
# set in8_min 5.0 * 0.90
# set in8_max 5.0 * 1.10

# Fans

label fan1 "Fan 1"
ignore fan1
set fan1_min 0

label fan2 "CPU Fan"
set fan2_min 1500

label fan3 "PWR Fan"
set fan3_min 1500

# Temperatures

label temp1 "SYS Temp"

label temp2 "CPU Temp"

ignore temp3

chip "acpitz-*"

# Temperatures

label temp1 "ThZ Temp"
# set temp1_crit 75
</pre>
'''Figyelem:''' egyes alaplapoknál az ACPI és ''hwmon'' közötti [http://hansdegoede.livejournal.com/7932.html belső I/O címütközés] miatt a 2.6.31-es kerneltől felfelé a szenzorok működéséhez az ''acpi_enforce_resources=lax'' kernel paraméter szükséges:
<pre>-rw------- root root /boot/grub/menu.lst

[...]
kernel /vmlinuz-2.6.31.1-grsec root=/dev/md3 ro acpi_enforce_resources=lax
[...]</pre>

===Asus CUV4X===
* A szenzor chip I2C SMBus Via Pro adapteren csatlakozó as99127f (Rev. 2).
* Szükséges kernel modulok: i2c_core, i2c_viapro, i2c_isa, w83781d, eeprom.
<pre>-rw-r--r-- root root /etc/sensors.conf

chip "as99127f-*"

# Asus won't release a datasheet so this is guesswork.
# Thanks to Guntram Blohm, Jack, Ed Harrison, Artur Gawryszczak,
# Victor G. Marimon and others for their feedback.

# Voltages

# Single power plane (A7V133, A7M266, CUV4X)
label in0 "VCore"
ignore in1

label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
# These last two may not make sense on all motherboards.
label in5 "-12V"
label in6 "-5V"

compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
# AS99127F rev.2 (same as w83782d)
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14

# adjust this if your vid is wrong; see doc/vid
set vrm 9.0

# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage

set in0_min vid*0.95
set in0_max vid*1.05
set in1_min vid*0.95
set in1_max vid*1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.90
set in4_max 12 * 1.10
set in5_max -12 * 0.90
set in5_min -12 * 1.10
set in6_max -5 * 0.95
set in6_min -5 * 1.05

# Depending on your motherboard, you may have to use any of two formulae
# for temp2. Quoting Artur Gawryszczak (edited to reflect subsequent fixes
# to the driver):
# "I guess, that the formula "(@*15/43)+25, (@-25)*43/15" is correct
# for those Asus motherboards, which get CPU temperature from internal
# thermal diode (Pentium Coppermine, and above), while no formula is needed
# for Athlon/Duron boards, which use a thermistor in the socket."
# An alternative formula was then found and reported by Victor G. Marimon.

# Asus A7V133, Asus A7M266
# No compute line is needed
# Asus CUV4X, Asus A7V8X
compute temp2 (@*15/43)+25, (@-25)*43/15
# Asus CUSL2, Asus CUV266-DLS, Asus TUSL2-C
# compute temp2 (@*30/43)+25, (@-25)*43/30

# See comments above if temp3 looks bad. What works for temp2 is likely
# to work for temp3 for dual-CPU boards, such as the CUV4X-D.

# Most Asus boards have temperatures settled like that:
label temp1 "M/B Temp"
label temp2 "CPU Temp"

# Most boards have no temp3 by default, except for dual-CPU boards.
# label temp3 "CPU 2 Temp"
ignore temp3

# Fans

label fan1 "CPU fan"
set fan1_div 4
set fan1_min 3000
ignore fan2
ignore fan3

# Temperature limits

set temp1_over 40
set temp1_hyst 37
set temp2_over 52
set temp2_hyst 47
# set temp3_over 52
# set temp3_hyst 47

# Ignore chassis intrusion detection alarm

ignore "alarms"</pre>

===Asus P4B===
Az SMBus PCI device-t a gyártó alapértelmezésben letiltotta (<small>"ASUS switches off the SMBus PCI Device in the i801 ICH chip. I spoke twice with the German support and learned that: 'We do not want the users to be irritated by just another PCI Device in the Win98 device manager.' Really funny :-)." - ld. [http://www.lm-sensors.org/browser/lm-sensors/trunk/prog/hotplug/README.p4b itt]</small>), így a sensors-detect nem talál szenzort. Az SMBus 2.6.18 vagy újabb kernelek esetében ezzel a scripttel engedélyezhető (eredetije [http://www.lm-sensors.org/browser/lm-sensors/trunk/prog/hotplug/unhide_ICH_SMBus itt]):
<pre>-rwxr-x--- root staff /usr/local/sbin/unhide_ICH_SMBus.sh

#!/bin/bash
# (C) Rudolf Marek <r.marek@assembler.cz>,
# Jean Delvare <khali@linux-fr.org>
#
# Thanks Jean Delvare and Oliver Dreier <oliver@dinux.de> for testing.
#
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License version 2
# as published by the Free Software Foundation

pcibus="/sys/bus/pci/slots/"
device="00:1f"

if [ "$UID" -ne 0 ] ; then
echo "You need to be root to run this script!"
exit 252
fi

smbus=`lspci -n -s $device.3 | grep -i '0c05: *8086'`
if [ -n "$smbus" ] ; then
echo "ICH SMBus is already there!"
lspci -s $device.3
exit
fi

intel=`lspci -n -s $device.0 | grep 8086`

if [ -z "$intel" ] ; then
echo "Not for your chipset - Intel (ICH) only"
exit 255;
fi
modprobe fakephp &> /dev/null

if [ ! -d "$pcibus" ] ; then
echo "You need the fake PCI hotplug driver! (fakephp.ko and 2.6 kernel)"
exit 255;
fi

echo "Enabling SMBus PCI device ..."

newval=$( printf '%x' $((0x$(setpci -s $device.0 f2.w) & 0xfff7)))
setpci -s $device.0 f2.w=$newval

echo "Rescanning the bus ..."
echo 1 > $pcibus/0000:$device.0/power 2>/dev/null
if [ ! -d "$pcibus/0000:$device.3" ] ; then
echo "Failed to enable the SMBUS"
exit 253;
fi

if [ ! -d "/sys/bus/pci/drivers/i801_smbus" ] ; then
echo "Loading i2c-i801 ..."
modprobe i2c-i801
if [ $? -ne 0 ] ; then
exit 251
fi
fi

lspci -s $device.3
echo "Done!"</pre>
Hátrány, hogy a script lefuttatása után nem lehet suspendelni az alaplapot, de ez a funkció szervereken amúgy sem használatos.

A futtatás előtt szükség van a ''pciutils'' csomag telepítésére:
<pre>apt-get install pciutils
/bin/bash /root/tmp/unhide_ICH_SMBus.sh</pre>
Ha a script futtatása sikeres, azt érdemes beütemezni minden reboot után egyszeri futtatásra, egyben a sensors megfelelő beállítására:
<pre>-rw-r--r-- root root /etc/cron.d/sensors-start

# Unhide SMBus to enable sensors running on P4B motherboard

PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin
MAILTO=root

@reboot root if [ -x /usr/local/sbin/unhide_ICH_SMBus.sh ]; then /usr/local/sbin/unhide_ICH_SMBus.sh; modprobe w83781d; modprobe eeprom; sensors -s; fi

# EOF</pre>
Szükséges kernel modulok: ''i2c_core'', ''i2c_dev'', ''i2c_i801'', ''i2c_isa'', ''w83781d'', ''eeprom''.
<pre>-rw-r--r-- root root /etc/sensors.conf

chip "as99127f-*"

# adjust this if your vid is wrong; see doc/vid
set vrm 9.0

# Voltage

label in0 "VCore 1"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"

compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
# AS99127F rev.2 (same as w83782d)
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14

# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage

set in0_min vid*0.95
set in0_max vid*1.05
set in1_min vid*0.95
set in1_max vid*1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.90
set in4_max 12 * 1.10
set in5_max -12 * 0.90
set in5_min -12 * 1.10
set in6_max -5 * 0.95
set in6_min -5 * 1.05

# Temperature

label temp1 "M/B Temp"
label temp2 "CPU Temp"

# Asus CUSL2, Asus CUV266-DLS, Asus TUSL2-C
compute temp2 (@*30/43)+25, (@-25)*43/30
# label temp3 "CPU 2 Temp"
ignore temp3

set temp1_over 40
set temp1_hyst 37
set temp2_over 65
set temp2_hyst 47
# set temp3_over 65
# set temp3_hyst 47

# Fans

label fan1 "CPU fan"
ignore fan2
ignore fan3</pre>
* [http://www.lm-sensors.org/browser/lm-sensors/trunk/prog/hotplug/README.p4b P4B ReadMe]
* [http://www.lm-sensors.org/browser/lm-sensors/trunk/prog/hotplug/unhide_ICH_SMBus Unhide SMBus]

===Asus P4C800===
* A szenzor chip I2C ISA buszon csatlakozó Winbond 83627-HF.
* Szükséges kernel modulok: ''i2c_core i2c_dev i2c_isa i2c_i801 w83627hf eeprom''.
<pre>-rw-r--r-- root root /etc/sensors.conf

chip "w83627thf-*" "w83637hf-*"

## Voltage ##

label in0 "VCore"
label in1 "+12V"
label in2 "+3.3V"
label in3 "+5V"
# label in4 "-12V"
label in7 "V5SB"
label in8 "VBat"

compute in1 ((28/10)+1)*@, @/((28/10)+1)
compute in3 ((34/51)+1)*@, @/((34/51)+1)
ignore in4
# compute in4 (5.14*@)-14.91, (@+14.91)/5.14
ignore in5
ignore in6
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
ignore in8

set vrm 9.0

set in0_min vid * 0.95
set in0_max vid * 1.05
set in1_min 12 * 0.90
set in1_max 12 * 1.10
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
# set in4_min -12 * 1.10
# set in4_max -12 * 0.90
set in7_min 5 * 0.95
set in7_max 5 * 1.05
# set in8_min 3.0 * 0.80
# set in8_max 3.0 * 1.20

## Temperature ##

label temp1 "M/B Temp"
label temp2 "CPU Temp"
ignore temp3

set temp1_over 50
set temp1_hyst 40
set temp2_over 75
set temp2_hyst 65
# set temp3_over 60
# set temp3_hyst 50

## Fans ##

ignore fan1
ignore fan2
label fan3 "CPU Fan"
set fan3_div 4
set fan3_min 2000</pre>
'''TODO:''' -12V (in4) helyes beállítása.
* [http://sadtuna.org/2005/3/26/gentoo-2004-2-asus-p4c800-deluxe Gentoo leírás]
* [http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83627HF_HGb.pdf Winbond 83627HF pdf leírás]

===Asus P5B Deluxe===
* A szenzorok i2c i801 (ISA) adapteren csatlakozó Winbond w83627ehf és a coretemp
* Szükséges kernel modulok: ''i2c_dev'', ''i2c_i801'', ''w83627ehf'', ''coretemp''
<pre>-rw-r--r-- root root /etc/sensors3.conf

# Winbond W83627EHF configuration originally contributed by Leon Moonen
# This is for an Asus P5P800, voltages for A8V-E SE.
# See also: http://www.lm-sensors.org/wiki/Configurations/Asus/P5B-E
chip "w83627dhg-*"

# Voltages

label in0 "VCore"
set in0_min 0.85
set in0_max 1.6

label in1 "+12V"
compute in1 @*(1+(56/10)), @/(1+(56/10))
set in1_min 12.0*0.9
set in1_max 12.0*1.1

label in2 "AVCC"
set in2_min 3.3*0.95
set in2_max 3.3*1.05

label in3 "3VCC"
set in3_min 3.3*0.95
set in3_max 3.3*1.05

ignore in4

label in5 "5VCC"
compute in5 @*(32/10), @/(32/10)
set in5_min 4.5
set in5_max 5.5

ignore in6
# compute in6 @*(1+(22/10)), @/(1+(22/10))
# set in6_min 5.0*0.95
# set in6_max 5.0*1.05

label in7 "VSB"
set in7_min 3.3*0.95
set in7_max 3.3*1.05

label in8 "VBAT"
set in8_min 3.3*0.95

# Fans

label fan1 "HDD Fan"
set fan1_min 1600

label fan2 "CPU Fan"
set fan2_min 1200

label fan3 "Rear Fan"
set fan3_min 1200

label fan4 "HDD Fan"
set fan4_min 1600

ignore fan5

# Temperatures

label temp1 "CPU Temp"
set temp1_max 95
set temp1_max_hyst 60

label temp2 "Sys Temp"
set temp2_max 95
set temp2_max_hyst 45

label temp3 "AUX Temp"
ignore temp3

# == CORE TEMPERATURES ==
# This requires the coretemp patch applied
# Maximums are autodetected by the driver depending on the CPU
# Core0
chip "coretemp-isa-0000"
label temp1 "Core0 Temp"

# Core1
chip "coretemp-isa-0001"
label temp1 "Core1 Temp"
</pre>
'''Figyelem:''' egyes alaplapoknál az ACPI és ''hwmon'' közötti [http://hansdegoede.livejournal.com/7932.html belső I/O címütközés] miatt a 2.6.31-es kerneltől felfelé a szenzorok működéséhez az ''acpi_enforce_resources=lax'' kernel paraméter szükséges:
<pre>-rw------- root root /boot/grub/menu.lst

[...]
kernel /vmlinuz-2.6.31.1-grsec root=/dev/md3 ro acpi_enforce_resources=lax
[...]</pre>

===IBM (x3105 AMD)===
Ez az alaplap van az [http://www-947.ibm.com/systems/support/supportsite.wss/selectproduct?familyind=5327319&typeind=5327400&osind=0&brandind=5000008&oldbrand=5000008&oldfamily=5327319&oldtype=0&taskind=7&psid=sr IBM System x3105 4347] 24G sorozatban.
* A szenzor chip I2C SMBus NForce adapteren csatlakozó ADT7476 (LM85 kompatibilis) plusz a PCI csatlakoztatású k8temp
* Szükséges kernel modulok: ''i2c_nforce2'', ''lm85'' - ez utóbbit paraméterrel kell betölteni:
<pre>-rw-r--r-- root root /etc/modules

[...]
# I2C adapter drivers
i2c-nforce2
# Chip drivers
# no driver for Analog Devices ADT7476 yet
lm85 ignore=1,0x2e
k8temp</pre>
<pre>-rw-r--r-- root root /etc/sensors3.conf

# Configuration for IBM 4347-24G (System x3105 amd64 Athlon 3500+)
#

chip "lm85-*"

# Voltage inputs

ignore in0
# set in0_min 1.5 * 0.95
# set in0_max 1.5 * 1.05

label in1 "V1.8"
set in1_min 1.8 * 0.95
set in1_max 1.8 * 1.05

label in2 "V3.3"
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05

label in3 "V5"
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05

label in4 "V12"
set in4_min 12 * 0.95
set in4_max 12 * 1.05

# Temperature inputs

label temp1 "CPU Temp"
ignore temp1

label temp2 "Board Temp"
set temp2_min 0
set temp2_max 55

label temp3 "Remote Temp"
ignore temp3
# set temp3_min 10
# set temp3_max 35

# Fan inputs

label fan1 "CPU Fan"
set fan1_min 500

label fan2 "Fan2"
ignore fan2

label fan3 "Fan3"
ignore fan3

label fan4 "Fan4"
ignore fan4

# Adjust fans speeds for actual pulses per rev
# compute fan1 @ * 2, @ / 2 # 1 pulse per rev
# compute fan2 @ / 2, @ * 2 # 4 pulse per rev

chip "k8temp-*"

# Don't set limits, unsupported here
label temp1 "Core0 Temp"
label temp3 "Core1 Temp"
</pre>

===IBM M71IXMB===
Ez az alaplap van az [http://www-947.ibm.com/systems/support/supportsite.wss/selectproduct?taskind=7&brandind=5000008&familyind=5166522&typeind=5211250&modelind=0&osind=0&psid=sr&continue.x=1 IBM eServer 206 8487] EWY sorozatban.
* A szenzor chip I2C SMBus I801 adapteren csatlakozó LM-85
* Szükséges kernel modulok: ''i2c_dev'', ''i2c_i801'', ''lm85''
* 2.6.31 feletti kernelnél (Squeeze) a natív driver confictol az ACPI-val lásd [http://www.lm-sensors.org/wiki/FAQ/Chapter3#Mysensorshavestoppedworkinginkernel2.6.31 itt], ezért (GRUB-2 esetén) kellhet a ''/etc/default/grub''-ba:
<blockquote><pre>-rw-r--r--root root /etc/default/grub

[...]
GRUB_CMDLINE_LINUX="acpi_enforce_resources=lax"
[...]</pre>
Ezután generáltassuk újra a Grub konfigurációját:
<pre>update-grub
reboot</pre></blockquote>
A recept:
<pre>-rw-r--r-- root root /etc/sensors3.conf
-rw-r--r-- root root /etc/sensors.d/ibm-206.conf (Squeeze)

# Configuration for the IBM eServer 206-EWY Intel M71IXMB

chip "adt7463-*" "lm85-*"

# Voltage inputs
# Depending on the hardware setup, the ADT7463 may not have in4.
ignore in0
label in0 "V1.5" # AGP on Intel S845WD1-E
set in0_min 1.5 * 0.95
set in0_max 1.5 * 1.05

label in1 "VCore"
set in1_min cpu0_vid * 0.95
set in1_max cpu0_vid * 1.05

label in2 "V3.3"
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05

label in3 "V5"
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05

ignore in4
label in4 "V12"
set in4_min 12 * 0.95
set in4_max 12 * 1.05

# Temperature inputs
label temp1 "CPU Temp"
set temp1_min 0
set temp1_max 60

label temp2 "Board Temp"
set temp2_min 0
set temp2_max 60

label temp3 "Remote Temp"
set temp3_min 0
set temp3_max 60

# Fan inputs
label fan1 "CPU_Fan"
compute fan1 @ * 2, @ / 2 # 1 pulse per rev
set fan1_min 1000

ignore fan2
label fan2 "Fan2"
compute fan2 @ / 2, @ * 2 # 4 pulse per rev
set fan2_min 1500

label fan3 "Rear Fan"
compute fan3 @ * 2, @ / 2 # 1 pulse per rev
set fan3_min 1500

ignore fan4
label fan4 "Fan4"
compute fan4 @ / 2, @ * 2 # 4 pulse per rev
set fan4_min 1500</pre>

===IBM Lenovo ThinkStation 6483===
A 6483-79G (S/N: LMYMTN9) gép alapján.
* A szenzor chip I2C ISA buszon csatlakozó ''SMSC SCH5027D-NW Super IO''
* Szükséges kernel modulok: ''i2c_core'' ''i2c_i801'' ''dme1737'' ''coretemp''
<pre>-rw-r--r-- root root /etc/sensors.d/lenovo-6483-79G.conf (Squeeze)

chip "sch5027-*"

# Voltages
label in0 "5VSB"
set in0_min 5.0 * 0.90
set in0_max 5.0 * 1.10
label in1 "Vcore"
set in1_min 0.85 * 0.95
set in1_max 1.36 * 1.05
label in2 "+3.3V"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
ignore in3
ignore in4
label in5 "3VSB"
set in5_min 3.3 * 0.90
set in5_max 3.3 * 1.10
label in6 "Vbat"
set in6_min 3.0 * 0.90
set in6_max 3.0 * 1.10

# Temperatures
ignore temp1
label temp2 "SIO Temp"
set temp2_max 65
ignore temp3

# Fans
label fan1 "CPU fan"
set fan1_min 500
ignore fan2
label fan3 "Rear fan"
set fan3_min 500
ignore fan4</pre>

===Intel D865PERL (desktop)===
* A szenzor chip I2C SMBus I801 adapteren csatlakozó LM-85 (kompatibilis)
* Szükséges kernel modulok: ''i2c_dev'', ''i2c_i801'', ''lm85''
<pre>-rw-r--r-- root root /etc/sensors3.conf

# Configuration for the Intel D865PERL
#
chip "adm1027-*"

# Voltage inputs
label in0 "V1.5" # AGP
label in1 "VCore"
label in2 "V3.3"
label in3 "V5"
label in4 "V12"
# ignore cpu0_vid

# Set voltage limits
set in0_min 1.5 * 0.95
set in0_max 1.5 * 1.05
set in1_min cpu0_vid * 0.95
set in1_max cpu0_vid * 1.05
# set in1_min 1.5 * 0.95
# set in1_max 1.5 * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05

# Temperature inputs
label temp1 "CPU Temp"
label temp2 "Board Temp"
label temp3 "Remote Temp"

# Set Temp Limits
set temp1_min 10
set temp1_max 65
set temp2_min 10
set temp2_max 50
set temp3_min 10
set temp3_max 50

# Fan inputs
label fan1 "CPU_Fan"
ignore fan2
# label fan2 "Fan2"
ignore fan3
# label fan3 "Fan3"
ignore fan4
# label fan4 "Fan4"
# Adjust fans speeds for actual pulses per rev
# compute fan1 @ * 2, @ / 2 # 1 pulse per rev
# compute fan2 @ / 2, @ * 2 # 4 pulse per rev
# compute fan3 @ * 2, @ / 2 # 1 pulse per rev
# compute fan4 @ * 2, @ / 2 # 1 pulse per rev

# Set Fan limits
set fan1_min 2000
# set fan2_min 4000
# set fan3_min 1000
# set fan4_min 1000

# Ignore chassis intrusion detection alarm

# ignore "alarms"</pre>

===Intel D915PBL (desktop)===
* A szenzor chip I2C SMBus I801 adapteren csatlakozó LM-85
* Szükséges kernel modulok: ''i2c_dev'', ''i2c_i801'', ''lm85''
<pre>-rw-r--r-- root root /etc/sensors3.conf

# Configuration for the Intel D915PBL
#
chip "lm85-*"

# Voltage inputs
label in0 "V1.5" # AGP
label in1 "VCore"
label in2 "V3.3"
label in3 "V5"
label in4 "V12"
ignore cpu0_vid

# Set voltage limits
set in0_min 1.5 * 0.95
set in0_max 1.5 * 1.05
set in1_min 1.375 * 0.95
set in1_max 1.375 * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05

# Temperature inputs
label temp1 "CPU Temp"
label temp2 "Board Temp"
label temp3 "Remote Temp"

# Set Temp Limits
set temp1_min 10
set temp1_max 65
set temp2_min 10
set temp2_max 50
set temp3_min 10
set temp3_max 50

# Fan inputs
label fan1 "CPU_Fan"
ignore fan2
# label fan2 "Fan2"
label fan3 "Fan3"
label fan4 "Fan4"
# Adjust fans speeds for actual pulses per rev
compute fan1 @ * 2, @ / 2 # 1 pulse per rev
# compute fan2 @ / 2, @ * 2 # 4 pulse per rev
compute fan3 @ * 2, @ / 2 # 1 pulse per rev
compute fan4 @ * 2, @ / 2 # 1 pulse per rev

# Set Fan limits
set fan1_min 2000
# set fan2_min 4000
set fan3_min 1000
set fan4_min 1000

# Ignore chassis intrusion detection alarm

# ignore "alarms"</pre>

===ServerWorks ServerSet III LE===
Ez az alaplap van a HP NetServer E-800-as gépekben.
* A szenzor SMBus PIIX4 adapteren elérhető Asus AS99127F.
* A szükséges kernel modulok: ''i2c_core, i2c_isa, i2c_piix4, w83781d, eeprom''.
<pre>-rw-r--r-- root root /etc/sensors.conf

chip "as99127f-*"

# Asus won't release a datasheet so this is guesswork.
# Thanks to Guntram Blohm, Jack, Ed Harrison, Artur Gawryszczak,
# Victor G. Marimon and others for their feedback.

# Dual power plane
label in0 "VCore 1"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
# These last two may not make sense on all motherboards.
label in5 "-12V"
label in6 "-5V"

compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
# AS99127F rev.2 (same as w83782d)
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14

# Depending on your motherboard, you may have to use any of two formulae
# for temp2. Quoting Artur Gawryszczak (edited to reflect subsequent fixes
# to the driver):
# "I guess, that the formula "(@*15/43)+25, (@-25)*43/15" is correct
# for those Asus motherboards, which get CPU temperature from internal
# thermal diode (Pentium Coppermine, and above), while no formula is needed
# for Athlon/Duron boards, which use a thermistor in the socket."
# An alternative formula was then found and reported by Victor G. Marimon.

# Asus CUV4X, Asus A7V8X
compute temp2 (@*15/43)+25, (@-25)*43/15

# Most Asus boards have temperatures settled like that:
# label temp1 "M/B Temp"
# label temp2 "CPU1 Temp"
# However, some boards have them swapped (A7N8X Deluxe rev.2,
# A7N8X-E Deluxe rev.2, CUV4X):
label temp1 "CPU1 Temp"
label temp2 "M/B Temp"
# Most boards have no temp3 by default, except for dual-CPU boards.
label temp3 "CPU2 Temp"

# adjust this if your vid is wrong; see doc/vid
# set vrm 9.0

# set limits to 5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage

set in0_min vid*0.95
set in0_max vid*1.05
set in1_min vid*0.95
set in1_max vid*1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.90
set in4_max 12 * 1.10
set in5_max -12 * 0.90
set in5_min -12 * 1.10
set in6_max -5 * 0.95
set in6_min -5 * 1.05

# examples for temperature limits
set temp1_over 40
set temp1_hyst 37
set temp2_over 52
set temp2_hyst 47
set temp3_over 40
set temp3_hyst 27

# Ignore chassis intrusion detection alarm

ignore "alarms"</pre>

===Shuttle XPC SBG1G2===
* A szenzor chip ISA buszon csatlakozó IT8712F.
* Szükséges kernel modulok: ''i2c_core it87 i2c_isa''.
Az ''i2c_i801'' betöltését ne engedjük, mert SMBus konkurrens olvasással(?) leállítja az SMBus-t (ekkor nincs sensors, csak a reboot segít)!
<pre>-rw-r--r-- root root /etc/sensors.conf

chip "it8712-*"

# Voltage monitors

label in0 "CPU"
label in1 "AGP"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
label in7 "Stdby"
label in8 "VBat"

compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((30/10) +1)*@ , @/((30/10) +1)
ignore in5
ignore in6
compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)

set in0_min 1.5 * 0.95
set in0_max 1.5 * 1.05
set in1_min 1.5 * 0.95
set in1_max 1.5 * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05
# set in5_max -12 * 0.85
# set in5_min -12 * 1.15
# set in6_max -5 * 0.95
# set in6_min -5 * 1.05
set in7_min 5 * 0.95
set in7_max 5 * 1.05
#the chip does not support in8 min/max

# Temperature
label temp1 "M/B Temp"
set temp1_over 45
set temp1_low 15
label temp2 "CPU Temp"
set temp2_over 50
set temp2_low 15
label temp3 "PWM Temp"
set temp3_over 50
set temp3_low 15

# Fans
label fan1 "CPU fan"
set fan1_min 1000
ignore fan2
# set fan2_min 3000
label fan3 "PWR fan"
set fan3_min 3000</pre>

===VIA Epia MII-10000===
* A szenzor chip ISA buszon csatlakozó V1211.
* Szükséges kernel modulok: ''i2c_viapro'', ''vt1211'' (<small>legalább 2.6.20.x kernelt igényel!</small>), ''eeprom''.

'''TODO!'''

==Irodalom==
* [http://en.wikipedia.org/wiki/I%C2%B2C I2C Wikipedia szócikk]
* [http://en.wikipedia.org/wiki/SMBus SMB Wikipedia szócikk]
* [http://hu.wikipedia.org/wiki/SNMP SNMP Wikipedia szócikk]
* [http://en.wikipedia.org/wiki/Self-Monitoring,_Analysis,_and_Reporting_Technology SMART Wikipedia szócikk]
* [http://www.winbond-usa.com/mambo/content/view/142/271/ Winbond hardware monitor chip leírások]
* [http://www.winbond-usa.com/mambo/content/view/143/273/ Winbond SuperIO chip leírások]
* [http://jdelvare.nerim.net/devel/lm-sensors/config/ Külső recept gyűjtemény]

Debian lm-sensors receptek - Laptörténet

KZoli: Új oldal, tartalma: „Az ''lm-sensors'' konfigurálása a hardver monitorozás "legszöszögősebb" része. A típusfüggő beállításokat a Debian Squeeze előtt a ''/etc/sensors.conf'' i…”